1()

NAME
pyocd-gdbserver - ARM Cortex-M programming tool

DESCRIPTION

pyocd-gdbserver is an ARM Cortex-M programming tool

  Summary

pyOCD is an Open Source python 2.7 based library for programming and debugging ARM Cortex-M microcontrollers using CMSIS-DAP.

Includes support for flashing new binaries, resetting the device, halt, step, resume read/write memory and set/remove breakpoints.

  Support

Firmware files included in the upstream source are NOT included in the Debian package due to a lack of source code. Target files can be downloaded separately from https://github.com/mbedmicro/pyOCD/tree/master/binaries

Available targets for use with --target option: lpc824, kinetis, w7500, kv11z7, lpc4088qsb, kv10z7, k20d50m, ncs36510, kl28z, kl25z, k82f25615, k28f15, maxwsnenv, max32600mbed, k22fa12, lpc4088, lpc4330, ke18f16, kl46z, stm32f103rc, kl82z7, lpc54114, kl43z4, kl26z, lpc11xx_32, lpc800, rtl8195am, kl05z, lpc1768, kw41z4, lpc4088dm, stm32f051, cortex_m, lpc11u24, kl02z, kw01z4, k64f, k22f, ke15z7, nrf51, nrf52, kl27z4, kw40z4, k66f18

  Usage

usage: pyocd-gdbserver [-h] [--version] [-p PORT_NUMBER] [-T TELNET_PORT] [--allow-remote] [-b BOARD_ID] [-l] [--list-targets]
    [--json] [-d LEVEL] [-t TARGET] [-n] [-r] [-C VECTOR_CATCH] [-s] [-f FREQUENCY] [-o] [-bh] [-ce | -se] [-u] [-hp] [-fp] [-S] [-G] [-c CMD [CMD ...]] [-da DAPARG [DAPARG ...]]

    PyOCD GDB Server

optional arguments:

-h, --help
    show this help message and exit

--version
    show program's version number and exit

-p PORT_NUMBER, --port PORT_NUMBER
    Write the port number that GDB server will open.

-T TELNET_PORT, --telnet-port TELNET_PORT
    Specify the telnet port for semihosting.

--allow-remote
    Allow remote TCP/IP connections (default is no).

-b BOARD_ID, --board BOARD_ID
    Connect to board by board id. Use -l to list all connected boards.

-l, --list
    List all connected boards.

--list-targets
    List all available targets.

--json
    Output lists in JSON format. Only applies to --list and --list-targets.

-d LEVEL, --debug LEVEL
    Set the level of system logging output. Supported choices are: debug, info, warning, critical, error

-t TARGET, --target TARGET
    Override target to debug. -n, --nobreak Disable halt at hardfault handler. (Deprecated)

-r, --reset-break
    Halt the target when reset. (Deprecated)

-C VECTOR_CATCH, --vector-catch VECTOR_CATCH Enable vector catch sources, one letter per enabled source in any order, or 'all' or 'none'. (h=hard
    fault, b=bus fault, m=mem fault, i=irq err, s=state err, c=check err, p=nocp, r=reset, a=all, n=none). (Default is hard fault.)

-s, --step-int
    Allow single stepping to step into interrupts.

-f FREQUENCY, --frequency FREQUENCY
    Set the SWD clock frequency in Hz.

-o, --persist
    Keep GDB server running even after remote has detached.

-bh, --soft-bkpt-as-hard
    Replace software breakpoints with hardware breakpoints.

-ce, --chip_erase
    Use chip erase when programming.

-se, --sector_erase
    Use sector erase when programming.

-u, --unlock
    Unlock the device.

-hp, --hide_progress
    Don't display programming progress.

-fp, --fast_program
    Use only the CRC of each page to determine if it already has the same data.

-S, --semihosting
    Enable semihosting.

-G, --gdb-syscall
    Use GDB syscalls for semihosting file I/O.

    -c CMD [CMD ...], --command CMD [CMD ...] Run command (OpenOCD compatibility).

    -da DAPARG [DAPARG ...], --daparg DAPARG [DAPARG ...] Send setting to DAPAccess layer.

COPYRIGHT
2006-2013 ARM Limited